Top 9 Stepper Motor Driver – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. TIMESETL

#ad

TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

#ad
TIMESETL #ad - Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Just wire up motors and power, easy to use.

Easy to use no assembly required. This l298n board comes ready to go. High quality main driver chip l298n, low calorific value, strong anti-interference, strong driving ability, afterflow diode protection, more stable and reliable for Arduino projects. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits. High efficient double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.
BrandTIMESETL #ad
ManufacturerTIMESETL #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberTXJ-061-EU
ModelL298N motor controller

2. MELIFE

#ad

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
MELIFE #ad - If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits. Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove.

Double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient. No assembly required. External size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Just wire up motors and power, easy to use. This l298n board comes ready to go. Main driver chip l298n, low calorific value, afterflow diode protection, strong anti-interference, strong driving ability, more stable and reliable for Arduino projects.
BrandMELIFE #ad
ManufacturerMELIFE #ad
Part Number15489

3. Longruner

#ad

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire

#ad
Longruner #ad - 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Cable length: about 20cm /8-inch. Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs. Stepper motor with a standard interface. Good after-sales service. A, c, b, d four-phase led indicates the status of the stepper motor work. Motor diameter: 1. 1 inches. Wire length:9. 05 inchs. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board.
BrandLongruner #ad
ManufacturerLongruner #ad
Part NumberLK67
ModelLK67
Warranty1 year warranty

4. HiLetgo

#ad

HiLetgo 2pcs A3967 Stepper Motor Drive Board EasyDriver Stepper Motor Driver for Arduino Raspberry Pi Robot

#ad
HiLetgo #ad - I. E. The easydriver has an on board voltage regulator for the digital interface that can be set to 5V or 3. 3v. Connect a 4-wire stepper motor and a microcontroller and you've got precision motor control. The easydriver is a simple to use stepper motor driver, compatible with anything that can output a digital 0 to 5V pulse or 0 to 3. 3v pulse if you solder SJ2 closed on the EasyDriver. Easydriver requires a 7v to 30V supply to power the motor and can power any voltage of stepper motor. 4, 6, or 8 wire stepper motors. Easydriver drives bi-polar motors, and motors wired as bi-polar.
BrandHiLetgo #ad
ManufacturerHiLetgo #ad
Part Number3-01-0831
Model3-01-0831

5. kuman

#ad

Kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 CNC Shield+UNO R3+Stepper Motor K75-CNC-UK, Red Blue

#ad
kuman #ad - 2 x end stops for each axis 6 in total. Pwm spindle and direction pins. Runs on 12-36V DC. Mcu: atmega328, usb interface: ATmega16U2. Latest cnc shield Version 3. 0 board. 4-axis support. 4pcs a4988 stepper Motor Driver with radiator.
Brandkuman #ad
Manufacturerkuman #ad
Height2.36 Inches
Length1.97 Inches
Weight0 Pounds
Width1.57 Inches
Part NumberK75-CNC-UK
ModelK75-CNC-UK
Warranty1 year

6. Gikfun

#ad

Gikfun EasyDriver Shield Stepper Motor Driver V44 A3967 for Arduino Pack of 3pcs EK1204

#ad
Gikfun #ad - Compatible with 4, 6, and 8 wire stepper motors of any voltage. Power supply range from 7v to 30V. A3967 microstepping driver. The higher the voltage, the higher the torque at high speeds.
BrandGikfun #ad
ManufacturerEsooho #ad
Height0.3 Inches
Length5 Inches
Weight0.02 Pounds
Width3 Inches
Part Numberunknown

7. LAFVIN

#ad

LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

#ad
LAFVIN #ad - Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1. 06in ; stepper Motor lines: 9. 45in. Stepper motor with a standard interface. Package content: 5 set 28byj-48 stepper motor + Uln2003 Driver Board +20pcs female to male Dupont cable as a gift. A, c, b, d four-phase led indicates the status of the stepper motor work. 5 line 4 phase can be used for ordinary uln2003 chip driver, connect to the 2 phase, support the development board,With convenient use, direct docking.
BrandLAFVIN #ad
ManufacturerLAFVIN #ad
Part NumberLA-003
Model903583

8. Usongshine

#ad

Usongshine DM542 Stepper Motor Controller Leadshine 2-Phase Digital Stepper Motor Driver 18-48 VDC Max. 4.2A for 57 86 Series Motor.

#ad
Usongshine #ad - High segmentation: 2, 4, 8, 64, 256. Suit for nema 17, 23 stepper motor,2-phase hybrid stepper motors Outer diameter: 57, 86mm. In the harsh environment of the power grid, it had strong anti-interference ability, high-precision positioning and high reliability.

H bridge bipolar constant phase flow subdivision driver. Precision electric casting control greatly reduces motor heating and halve the chattering automatically at rest. 5, 50, 16, 128, 125, 10, 25, 32, 200. Low noise. Output current dip switch is adjustable. Optical isolation signal input, strong anti-interference ability with over voltage, over light and other protective functions. 20khz chopping frequency. Low speed without vibration.
BrandUsongshine #ad
ManufacturerUsongshine #ad

9. Atnsinc

#ad

6 PCS 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino

#ad
Atnsinc #ad - The stepping motor is a kind of mechanical and electrical device that converts electrical pulses into angular displacement. A, c, b, d four-phase led indicates the status of the stepper motor work.

Drive module board sizein: 1. 37 * 1. 18 * 06in; stepper Motor diameter: 1. 06in; stepper Motor lines: 9. 45in. 5 line 4 phase can be used for ordinary uln2003 chip driver, Connect to the 2 phase, With convenient use, Support the development board, direct docking. Great packing in a box : 6 pcs uln2003 Stepper Motor + Driver Board with a little gift. Come with a standard interface, when used directly pluggable.
BrandAtnsinc #ad
ManufacturerAtnsinc #ad
Part NumberAtnsinc-01
ModelAtnsinc-01